ASTM A249 Tubing

Stockist and supplier of ASTM A249 Tubing, Tuberia ASTM A249, ASTM A249 TP304, ASTM A249 TP316L, ASTM A249 TP304L. ASTM A249 TYPE 304 Price in India. Exporter of Tubos ASTM A249 in Mumbai

ASTM A249 / A249M - 16a

An ASTM designation number identifies a unique version of an ASTM standard.

A249 / A249M - 16a

A = ferrous metals;

249 = assigned sequential number

M = SI units

16 = year of original adoption (or, in the case of revision, the year of last revision)

a = indicates subsequent revision in same year

Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes

Ref: https://www.astm.org/Standards/A249.htm

Looking to buy Alloy 600 Tubing? Inconel 600 Tubing?

Check Today's price of Alloy 600 Tubing in India

Alloy 600 Tubing supplier

       

ASTM A249 / A249M-16a, Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes

Abstract

This guide specifies standard specification for nominal-wall-thickness welded tubes and heavily cold worked welded tubes made from the austenitic steels with various grades intended for such use as a boiler, superheater, heat exchanger, or condenser tubes. Heat and product analysis shall conform to the requirements as to chemical composition for carbon, manganese, phosphorous, sulfur, silicon, chromium, nickel, molybdenum, nitrogen, copper, and others. All materials shall be furnished in the heat-treated condition in accordance with the required solution temperature and quenching method. When the final heat treatment is in a continuous furnace, the number of tubes of the same size and from the same heat in a lot shall be determined from the prescribed size of the tubes. The material shall conform to the prescribed tensile and hardness properties such as tensile strength, yield strength, elongation, and Rockwell hardness number. The steel shall undergo mechanical tests such as tension test, flattening test, flange test, reverse-bend test, hardness test, and hydrostatic or nondestructive electric test. The grain size of different grades of steel shall be determined in accordance with the test methods.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification2 covers nominal-wall-thickness welded tubes and heavily cold worked welded tubes made from the austenitic steels listed in Table 1, with various grades intended for such use as boiler, superheater, heat exchanger, or condenser tubes.

1.2 Grades TP304H, TP309H, TP309HCb, TP310H, TP310HCb, TP316H, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP309S, TP309Cb, TP310S, TP310Cb, TP316, TP321, TP347, and TP348, and are intended for high-temperature service such as for superheaters and reheaters.

1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 12 in. [304.8 mm] in outside diameter and 0.015 to 0.320 in. [0.4 to 8.1 mm], inclusive, in wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification.

1.4 Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] in inside diameter or 0.015 in. [0.4 mm] in thickness.

1.5 Optional supplementary requirements are provided and, when one or more of these are desired, each shall be so stated in the order.

1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

1.7 The following safety hazards caveat pertains only to the test method described in the Supplementary Requirements of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 

Related searching:

ASTM A249, ASTM A249 PDF, ASTM A249 TUBING, ASTM A249 TP304, ASTM A249 OR A269, ASTM A249/A269, ASTM A249 TP316L, ASTM A249 TOLERANCE, ASTM A249 TP304 SPECIFICATION, ASTM A249 304L, ASTM A249 CHEMICAL COMPOSITION, ASTM A249 STAINLESS TUBE, ASTM A249/A249M, ASTM A249 EQUIVALENT, NORMA ASTM A249, ASTM A249 PROPERTIES, ASTM A249 PRESSURE RATING, ASTM A249 SEAMLESS, ASTM A249 SPEC, ASTM A249 STANDARD, ASTM A249/SA 249, ASTM A249 TP304L, ASTM A 249-TP 316, ASTM A249 TYPE 304, TUBOS ASTM A249, TUBERIA ASTM A249, ASTM A213 VS A249, ASTM A269 VS A249, ASTM A249 316L, ASTM A249 304, ASTM A249-95A

Pipe, Tube & Tubing

Sheet, Plate

Round Bar & fasteners


Trademark Notice

Aircraft Materials & Aerospace Materials Specialist